Den Stihl 066 motorsåg är ett kraftfullt verktyg som klarar även de tuffaste skäruppgifterna. i alla fall, like any mechanical device, it may encounter issues from time to time. If you’re experiencing problems with your Stihl 066 motorsåg, oroa dig inte. I den här artikeln, we will explore some tips about Stihl 066 Felsökning to get your chainsaw back up and running in no time.
Problem 1: Saw chain stops under load at full throttle
Orsaker
- Clogged or dirty air filter restricting airflow to the engine.
- Fuel mixture is incorrect, either too lean or too rich.
- Carburetor is dirty or needs adjustment.
- Spark plug is faulty or worn out.
- Engine compression is low due to worn piston rings or cylinder.
Lösningar
- Clean or replace the air filter to ensure proper airflow.
- Check and adjust the fuel mixture according to the manufacturer’s specifications.
- Rengör förgasaren eller låt den servas professionellt.
- Replace the spark plug with a new one that meets the manufacturer’s recommendations.
- If the compression is low, consult a professional for further inspection and potential repairs.
Problem 2: Höga ljud
Orsaker
- Loose or damaged components, such as the chain, svärd, or clutch.
- Worn or damaged bearings in the engine or chain sprocket.
- Excessive chain tension.
- Insufficient lubrication to the chain and guide bar.
Lösningar
- Tighten or replace any loose or damaged components.
- Inspect and replace worn or damaged bearings.
- Adjust the chain tension to the manufacturer’s specifications.
- Ensure proper lubrication by regularly applying oil to the chain and guide bar.
Problem 3: The sprocket wears rapidly
Orsaker
- Felaktig kedjespänning, either too tight or too loose.
- Lack of lubrication to the chain and guide bar.
- Worn or damaged sprocket teeth.
- Improper chain sharpening technique.
Lösningar
- Adjust the chain tension to the manufacturer’s recommended specifications.
- Regularly lubricate the chain and guide bar to reduce friction and wear.
- Replace the sprocket if the teeth are worn or damaged.
- Ensure proper chain sharpening technique to prevent excessive wear on the sprocket.
Problem 4: Saw chain does not stop activated
Orsaker
- Faulty or worn-out chain brake mechanism.
- Damaged or misaligned chain brake components.
- Malfunctioning chain brake handle or trigger.
Lösningar
- Inspect the chain brake mechanism for any damage or wear and replace any faulty parts.
- Ensure the chain brake components are properly aligned and functioning correctly.
- If the chain brake handle or trigger is not working, byt ut den mot en ny.
Problem 5: Chain receives no oil
Orsaker
- Clogged or dirty oil channels or oil filter.
- Faulty or clogged oil pump.
- Insufficient oil in the reservoir.
- Damaged or worn oil delivery system components.
Lösningar
- Clean the oil channels and oil filter to remove any clogs or dirt.
- Check and repair or replace the oil pump if it is faulty or clogged.
- Ensure there is enough oil in the reservoir to provide proper lubrication.
- Inspect and replace any damaged or worn components in the oil delivery system.
Problem 6: Oil pump delivers insufficient
Orsaker
- Clogged or dirty oil channels or oil filter.
- Worn or damaged oil pump components.
- Insufficient oil in the reservoir.
- Malfunctioning oil pump drive gear.
Lösningar
- Clean the oil channels and oil filter to remove any clogs or dirt.
- Replace any worn or damaged oil pump components.
- Ensure there is enough oil in the reservoir to provide proper lubrication.
- Check and replace the oil pump drive gear if it is malfunctioning.
Problem 7: Starter rope does not rewind
Orsaker
- Starter spring is damaged or worn.
- Starter pulley is damaged or worn.
- Starter rope is tangled or damaged.
Lösningar
- Replace the starter spring if it is damaged or worn.
- Replace the starter pulley if it is damaged or worn.
- Untangle or replace the starter rope if it is tangled or damaged.
Problem 8: Engine runs roughly, misfires, temporary loss of power
Orsaker
- Smutsigt eller igensatt luftfilter.
- Incorrect fuel mixture.
- Dirty carburetor.
- Worn or fouled spark plug.
- Low engine compression.
- Malfunctioning ignition system.
Lösningar
- Clean or replace the air filter to ensure proper airflow.
- Check and adjust the fuel mixture according to the manufacturer’s specifications.
- Rengör förgasaren eller låt den servas professionellt.
- Replace the spark plug with a new one that meets the manufacturer’s recommendations.
- If the compression is low, consult a professional for further inspection and potential repairs.
- Inspect and repair or replace any malfunctioning ignition system components.
Problem 9: No spark
Orsaker
- Defekt tändstift.
- Malfunctioning ignition coil.
- Damaged or disconnected spark plug wire.
- Faulty stop switch.
Lösningar
- Replace the spark plug with a new one that meets the manufacturer’s recommendations.
- Inspect and replace the ignition coil if it is malfunctioning.
- Check and repair or replace any damaged or disconnected spark plug wires.
- Inspect and replace the stop switch if it is faulty.
Problem 10: Dålig acceleration
Orsaker
- Smutsigt eller igensatt luftfilter.
- Incorrect fuel mixture.
- Dirty carburetor.
- Worn or fouled spark plug.
- Malfunctioning ignition system.
- Felaktig kedjespänning.
Lösningar
- Clean or replace the air filter to ensure proper airflow.
- Check and adjust the fuel mixture according to the manufacturer’s specifications.
- Rengör förgasaren eller låt den servas professionellt.
- Replace the spark plug with a new one that meets the manufacturer’s recommendations.
- Inspect and repair or replace any malfunctioning ignition system components.
- Adjust the chain tension to the manufacturer’s recommended specifications.
Problem 11: Idle speed too high
Orsaker
- Smutsigt eller igensatt luftfilter.
- Malfunctioning carburetor.
- Malfunctioning throttle linkage.
- Worn or damaged engine components.
Lösningar
- Clean or replace the air filter to ensure proper airflow.
- Inspect and repair or replace the carburetor if it is malfunctioning.
- Inspect and repair or replace the throttle linkage if it is malfunctioning.
- Consult a professional for further inspection and potential repairs if worn or damaged engine components are the cause.
Problem 12: Engine overheating
Orsaker
- Lack of proper lubrication.
- Clogged or dirty air filter.
- Incorrect fuel mixture.
- Dirty carburetor.
- Worn or damaged engine components.
Lösningar
- Ensure proper lubrication by regularly applying oil to the chain and guide bar.
- Clean or replace the air filter to ensure proper airflow.
- Check and adjust the fuel mixture according to the manufacturer’s specifications.
- Rengör förgasaren eller låt den servas professionellt.
- Consult a professional for further inspection and potential repairs if worn or damaged engine components are the cause.
Slutsats
By troubleshooting the common issues that can arise with your Stihl 066 motorsåg, you can save time and money by resolving the problems yourself. Remember to always prioritize safety when working with power tools and consult the manufacturer’s manual for specific instructions. With the right knowledge and a little troubleshooting know-how, you can keep your Stihl 066 chainsaw in optimal condition and enjoy its reliable performance for years to come.
Innehåll
show